Sweaters are everywhere. Men, women, children and teenagers wear these popular outfits throughout the year. Although the sweater itself is very fashionable, the richly embroidered design increases the appeal of the garment and adds value. Of course, designing on a sweater can sometimes be tricky.
Due to its nature, sweater knitwear often causes headaches for the embroiderer. The thread is "eaten". The entire design has disappeared. The fabric itself is wrinkles and waves. Sometimes the design is cut from the clothes even by needle penetration. Fortunately, you can avoid these potential problems and get high quality results.
These adjustments need to be made from the beginning of any work. It is well designed in the embroidery of sweater knitwear. You need to let your digitizer know in advance that the design will be used for sweaters. Even better, give the digitizer an actual fabric sample for testing purposes. Simply communicating with the digitizer can save you a lot of hassle.
There are some tricks for digitizing designs that are stitched on knitted fabrics. In order to stabilize the fabric and lay the foundation for the design, try increasing the number of pad stitches in the design. Also try to keep the design elements large and recommend not to try small details or fine lines. Instead of a logo that usually consists of symbols and letters, why not advise your customers to try only one symbol? It's lower-key and has more graphics impact - easier to produce. Once your design is digitized, you can start splicing. Follow some guidelines and you should be able to do high quality work.
preparation
Taking the time and effort to prepare an embroidery knitwear may mean a difference between a beautiful design and a simple shoddy work. At this stage, your main goal is to stabilize the structure. This can be achieved by a combination of a backing, a dissipative spray adhesive and a topping. When using knitwear, always use a cut backing instead of tearing. It is a good idea to spray the backing with an adhesive before placing the backing on the garment. Gently press the backing onto the garment. Make sure not to use too much force as this will distort the ribs. If your design lacks a large amount of liner, use some type of plastic or water soluble topping to compensate. For best results, gently apply your primer with a spray adhesive and press it on your clothes with your palm. By sandwiching the knit between the backing and the top, you can increase its stability. The adhesive spray helps prevent the garment from slipping while the machine is running.
Hoop tip
Because knitted fabrics are so stretchable, special care should be taken when embroidering. The knitted fabric stretches in all directions. To avoid twisting the fabric, gently pull the knit material only in the vertical direction.
Make sure the ribbing of the fabric is straight. If it is placed on the ring at an angle, it will cause your design to be distorted and wrinkled. Put the clothes on your hoop and carefully smooth the wrinkles. Then, gently press the top frame into the bottom. Again ensure that all ribs are parallel to each other. The knit fabric should be taut, but not so tight that the fabric stretches and deforms.
In addition to stretching and deforming the garment, too tight a hoop can cause other problems, especially for knitting a finer knitted fabric. An embroiderer involves a horror story of being cheated. A customer gave him an expensive cashmere sweater to embroider. He quickly hung the item, placed it on his machine and sewed a beautiful design. However, when the hoop is pulled open, the entire area has fallen off the sweater. Of course he learned the lesson that day! Although this is an extreme example, a tight hoop can cut the fibers of the knit fabric and leave an unsightly ring around the design that does not disappear. Another factor to consider is the size of the hoop.
It is best to match the hoop size as much as possible to the design size. Some people prefer to use an 8-inch hoop for a 2-inch design. This is not a good idea, as too many hoops tend to cause the knit fabric to pull and wrinkle.
Sewing technology
Once the clothes are properly hung, you can start sewing your design. If you have a lot of orders, it's a good idea to get the fabric or clothing samples you will be using and do some testing. In this way, you can determine the optimal machine settings for a particular product. Always use ball needles on knitwear. Conventional needles can cut the threads of the knitted fabric and even cut the stitched design into the garment itself.
The size of the needle depends on the type of sweater knitting. Fine knitting requires a 9 or 10 ball needle. 10 to 11 stitches work best for medium knitwear. Also, heavier knits make it necessary to use 12 or 14 size needles. In order to get better results, it is also wise to reduce the speed of the machine.
I hope that by following these suggestions, you will be able to make beautiful embroidery on today's popular sweaters.
Orignal From: Embroidered knit sweater tips
No comments:
Post a Comment